EasyFix Enterprises

EasyFix
“Products For The Care and Repair of Marx Figures”

Product Description

EasyPrime Activator was designed to solve the problem of adhering ABS, Polypropylene, Polyethylene, PTFE (Poly Fluoro Ethylene), and Delfrin. When allowed to evaporate, the active ingredients of EasyPrime can change the molecular structure of the plastic surface. It will not cause discolorations or harm plastic surfaces in any way.
Caution: Contains petroleum distillates. If swallowed, do not induce vomiting. Drink Mild or water and seek immediate medical attention. Highly flammable, store at room temperature, do not expose to open flame. Harmful or fatal if swallowed. Do not inhale vapors. It may stick skin or eyelids together in seconds. Latex or Rubber gloves and adequate eye protection is highly recommended. Keep out of reach of children. Clean off hands with soap and water or hand-cleaner. Flush eyes with special eyewash. Consult eye specialist or health care professional in the event of accident.
EasyFill is a suitable filling material designed for use in combination with EasyFix Adhesive.
It is a non-toxic substance. It does not damage the environment and can be disposed of together with household waste.

EasyPrep was designed to remove grease, oil, grime, dirt, and many unknown contaminants from surfaces to be repaired with EasyFix
Caution: Contains Sodium Meta-Silicate. Avoid contact with skin and eyes. Latex or Rubber gloves and adequate eye protection is highly recommended. Thoroughly wash all contaminated clothing before reuse. May cause burns or irritation. Harmful if swallowed. If swallowed, give large quantities of water or milk; follow with citrus juice or dilute vinegar and call physician, emergency room, or poison control center. EYE CONTACT: Flood with plenty of water for at least 15 minutes. Get medical attention promptly. SKIN CONTACT: Wash thoroughly with soap and water. If redness of skin occurs, discontinue use and consult physician immediately. KEEP OUT OF REACH OF CHILDREN AND ANIMALS!
Caution: Strong EasyPrep solutions may remove or degloss paints, enamels, and plastic surfaces. Not for use on wood or glass.

EasyRelease is suitable for preventing adhesives from adhering to unwanted surfaces.
Caution: Contains petroleum distillates. If swallowed, do not induce vomiting. Drink Mild or water and seek immediate medical attention. Highly flammable, store at room temperature, do not expose to open flame. Harmful or fatal if swallowed. Do not inhale vapors. It may stick skin or eyelids together in seconds. Latex or Rubber gloves and adequate eye protection is highly recommended. Keep out of reach of children. Clean off hands with soap and water or hand-cleaner. Flush eyes with special eyewash. Consult eye specialist or health care professional in the event of accident. Contains no Silicone.

EasyClean is a state-of-the-art, deep cleaning, and multi-purpose foam cleaner. Designed for safe use on all plastics, vinyl, porcelain, fabric, painted wood and much more.
Caution: Contains 2-Butoxyethanol, surfactants, and fragrance. Rinse off skin after use. Avoid eye contact and prolonged skin contact. Flush eyes with water for 15 minutes. If redness or irritation continues for a prolonged period of time seek medical attention. Keep out of reach of children.

Instructions for use of EasyFix products EasyPrep is a concentrated powder or crystals designed to dissolve in water before use. To prepare surface for repair mix 1/8 cup cleaner with 1 gallon of warm water. Allow powder to dissolve completely. Soak small brush in solution and scrub repair area briskly. Do not allow to dry on surface. Rinse thoroughly with warm water and allow to completely air dry.
For deep cleaning greasy or oily surfaces mix 1/8 cup per two gallons water. Brush on or submerge item to be cleaned. Allow to soak for 5 minutes. Do not allow surface to dry. Rinse with warm water. Repeat as necessary.

EasyPrime Activator is first brushed on to the carefully cleaned repair area. Then, after 2 minutes of flash off time the repair can be performed with EasyFix.

EasyRelease can be lightly brushed onto any surface that requires protection from adhesion. Perfect for moving parts. Shake well before use. Brush on in thin coats. Allow to dry between coats. Two or three coats should be sufficient if to protect surface from adhering to unwanted surface if adhesive accidentally comes into contact. In areas where adhesive is likely to come into contact with unwanted surface more coats may be required.
If release agent comes in contact with primed repair surface each step must be repeated from the beginning.

EasyFix Adhesive is applied in a thin layer to the properly cleaned and primed repair surface. The thinner the layer of adhesive, the better the joint. Strongly absorbent surfaces require more adhesive. Don’t rub in. Allow to stand for a few minutes. Different materials dry at different rates. Best results are obtained at room temperature. After 7-8 hours any material will be firmly set. Moisture and heat are to be avoided at all costs. Keep bottles in upright position.

EasyFill is for use in applications where splits, cracks, chip, or voids have occurred. Put on “shifts” of EasyFill of approximately 2-3mm thickness and then impregnate thoroughly with EasyFix. To prevent from dropping through holes, just put a piece of paper underneath to form a temporary “dam”. Depending on the situation you may also put on EasyFix first and then spread on EasyFill. This variation proves most effective to make welds at seams and corners. Make sure the filling material is thoroughly soaked with adhesive. After two or three minutes the hardened joint can be processed mechanically.

EasyClean is a top notch, industrial strength, multi-purpose cleaner that is both mild and tough. It rinses off easily but cleans deep-seated, stubborn grime and grunge from plastic and vinyl surfaces better than any other household cleaner. It is the perfect all-purpose cleaner for most collectibles.
Shake well before use. Spray liberally onto surface to be cleaned. Allow EasyClean to work for 30 – 40 seconds. Scrub with stiff brush. Wipe clean with cloth or rinse with warm water.
May also be used on plastics and vinyl as a dip or bath. Soak for 15 minutes, brush vigorously with stiff brush, and rinse with warm water. Repeat as necessary (but it probably won’t be!).
Unlike other cleaners and adhesives, EasyFix products are fully guaranteed to work as described, or the purchase price is fully refundable. Simply return unused portions for a full refund of the sale price.

Got a Question? We'd like to help. 620-224-2945 or EMAIL